How-to with pics: Repaint and pretty-up your controls
Posted: Mon Jul 05, 2010 4:46 pm
OK, with thanks and props to FasterSpider for the steer on the orange paint, here's a very quickie how-to pretty up your controls.
Step 1, Get them off the bike, and on the right-side control, remove the teeny circlip underneath the kill switch, and remove the orange kill switch. BEWARE! There is a small ball bearing that provides the positioning and creates the detents. As soon as you lift the orange switch it will fall out. Be ready.
Step 2, Clean them really well, particularly between the raised letters, with an old toothbrush. A Q-Tip and some spray contact cleaner will do a nice job on the connector, and the little boots with the connectors for the clutch and brake switches will clean up this way too. Get the body of the pods good and dull, I finished the job with alcohol.
Step 3, Mask them. It's easy to mask the wires and the buttons for the horn and starter with masking tape, and you do not want overspray getting onto the kill switch contacts or into the internals. Plug the bar holes with a wadded up paper towel or something.
Step 4, Hang them up from their (masked) wires and (spray) paint them. I used SEM Trim paint and it worked really well. Has a teeny bit of lustre, very durable, goes on easily. Great stuff. 2 light coats was fine. Pretty sure I got the SEM stuff from Eastwood.
Step 5, Paint the raised lettering. For this I used ModelMaster Flourescent Red Orange # FS28913. I think I got this from eHobbies. Google knows where to get it.
This is the tricky bit, and Google coughed up this technique too: Go bum a cigarette. Marlboro Lights work very well I learned :) Shake/stir the paint well. Take the filter and dab it in the very little amount of paint in the cap.
Take the cigarette and dab it very carefully onto the raised lettering. Go slow, and make certain to hold it flat and build it up. You'll find that you can vary the thickness of the paint this way, and if you go too fast you'll fill in stuff like the center of the letter "A".
There you have it. I attempted painting the kill switch and starter/horn buttons on my crappy test switch, with the orange paint and a brush, and failed. Airbrushing these might be the way to go, haven't attempted that yet.
Have fun and good luck!
Step 1, Get them off the bike, and on the right-side control, remove the teeny circlip underneath the kill switch, and remove the orange kill switch. BEWARE! There is a small ball bearing that provides the positioning and creates the detents. As soon as you lift the orange switch it will fall out. Be ready.
Step 2, Clean them really well, particularly between the raised letters, with an old toothbrush. A Q-Tip and some spray contact cleaner will do a nice job on the connector, and the little boots with the connectors for the clutch and brake switches will clean up this way too. Get the body of the pods good and dull, I finished the job with alcohol.
Step 3, Mask them. It's easy to mask the wires and the buttons for the horn and starter with masking tape, and you do not want overspray getting onto the kill switch contacts or into the internals. Plug the bar holes with a wadded up paper towel or something.
Step 4, Hang them up from their (masked) wires and (spray) paint them. I used SEM Trim paint and it worked really well. Has a teeny bit of lustre, very durable, goes on easily. Great stuff. 2 light coats was fine. Pretty sure I got the SEM stuff from Eastwood.
Step 5, Paint the raised lettering. For this I used ModelMaster Flourescent Red Orange # FS28913. I think I got this from eHobbies. Google knows where to get it.
This is the tricky bit, and Google coughed up this technique too: Go bum a cigarette. Marlboro Lights work very well I learned :) Shake/stir the paint well. Take the filter and dab it in the very little amount of paint in the cap.
Take the cigarette and dab it very carefully onto the raised lettering. Go slow, and make certain to hold it flat and build it up. You'll find that you can vary the thickness of the paint this way, and if you go too fast you'll fill in stuff like the center of the letter "A".
There you have it. I attempted painting the kill switch and starter/horn buttons on my crappy test switch, with the orange paint and a brush, and failed. Airbrushing these might be the way to go, haven't attempted that yet.
Have fun and good luck!
Great use for the cancer sticks!