Shim for Caliper Mounting Bracket

Post Reply
oldbikerdude
ICOA Member
ICOA Member
Posts: 135
Joined: Mon Nov 20, 2017 9:40 am
Location: Waterloo, Ontario, Canada

Shim for Caliper Mounting Bracket

Post by oldbikerdude »

There is a part number which I can't find.
It is the stainless steel shim that fits to the bracket where the caliper get mounted. One of the retaining tabs is broken off and won't stay in place.
IMG_4031.jpg
IMG_4032.jpg
The parts fiche does not have this part listed,
Anyone know what the correct part number is, likely same as the 81, but guessing on this.
Went to local Honda dealer, they also could not find it. Apparently missing from parts fiche.
Thanks,
You do not have the required permissions to view the files attached to this post.

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4736
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: Shim for Caliper Mounting Bracket

Post by daves79x »

It is not a separate part number. You just have to scrounge them up, and they're hard to find. I'd be happy with the one you have, just epoxy it on and you're good to go. Louis probably would sell you one separately if you really wanted one.

Dave

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: Shim for Caliper Mounting Bracket

Post by EMS »

This may be the part you are looking for 45112-MA2-006

then there are also 45112-410-006 and 43112-110-006

I can't really tell what "hanger" you are showing. Is this an original CBX part?

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4736
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: Shim for Caliper Mounting Bracket

Post by daves79x »

45112-MA2-006 is the front caliper shim, but I can't tell you if the rear (which the poster is looking for) is the same part. There are two or three sizes of that part used on Hondas of that era.

Dave

oldbikerdude
ICOA Member
ICOA Member
Posts: 135
Joined: Mon Nov 20, 2017 9:40 am
Location: Waterloo, Ontario, Canada

Re: Shim for Caliper Mounting Bracket

Post by oldbikerdude »

The front rotors are the thicker vented discs and the rear is solid disc (thinner than front).
So for sure the fronts will not fit on the rear.
The first pic above is the rear brake caliper retainer for the 82.
Thanks for the help.

oldbikerdude
ICOA Member
ICOA Member
Posts: 135
Joined: Mon Nov 20, 2017 9:40 am
Location: Waterloo, Ontario, Canada

Re: Shim for Caliper Mounting Bracket

Post by oldbikerdude »

So here's what I did, I ordered two parts
1) 43112-445-631 this is the rear retainer on my goldwing.
2) 45112-445-631 this is the front retainer.
Thinking if it doesn't fit the CBX, I still can use them for the GW.
Look like the 43112 fits exactly like the original one on the CBX.
The other will fit but center portion won't clear the rotor, unless I dremel it off.
Will get pic later and show.
Thanks for all the help.

oldbikerdude
ICOA Member
ICOA Member
Posts: 135
Joined: Mon Nov 20, 2017 9:40 am
Location: Waterloo, Ontario, Canada

Re: Shim for Caliper Mounting Bracket

Post by oldbikerdude »

Here is a pic of the new one I used part number 43112-445-631.
IMG_4282.jpg
You do not have the required permissions to view the files attached to this post.

Post Reply

Return to “BRAKES: Calipers, Pads, Lines, Rotors, Upgrades & Fixes”