Painting my valve cover


6Pipes
ICOA Member
ICOA Member
Posts: 108
Joined: Tue Oct 05, 2010 6:47 pm
Location: Morgantown, WV
Location: Morgantown, West Virginia, USA

Painting my valve cover

Post by 6Pipes »

Just thought I'd pass this on for fun.
I just painted my valve cover with a few coats of Duplicolor BGM0535. Man, is that paint sensitive to oil film! I washed the valve cover in Dawn detergent twice with a sponge and then a third time with Dawn and steel wool. Thinking that it was squeaky clean, I applied the first coat of paint and it curdled on contact. After several applications of brake clean ( I don't have any alcohol or toluene) and a couple more detergent scrubes, I finally got the paint to stick properly. Just a heads up for anyone else doing this project. Make sure you get the darn paint surface completely, totally and absolutely free of even the slightest "hint" of oil.

tevan
ICOA Member
ICOA Member
Posts: 699
Joined: Sun Apr 25, 2010 8:47 am
Location: Charleston, Illinois, USA
Location: Charleston, Illinois, USA

Re: Painting my valve cover

Post by tevan »

After you paint it are you going to put clear over it?

6Pipes
ICOA Member
ICOA Member
Posts: 108
Joined: Tue Oct 05, 2010 6:47 pm
Location: Morgantown, WV
Location: Morgantown, West Virginia, USA

Re: Painting my valve cover

Post by 6Pipes »

Tevan,
It's already back on the engine. Never thought about clear. Sounds like a good idea though!

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4737
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: Painting my valve cover

Post by daves79x »

No clear on engine paint - never was from Honda and not a good idea.

Dave

tevan
ICOA Member
ICOA Member
Posts: 699
Joined: Sun Apr 25, 2010 8:47 am
Location: Charleston, Illinois, USA
Location: Charleston, Illinois, USA

Re: Painting my valve cover

Post by tevan »

I was wandering about that. I am just about ready to paint my 81 cover it is in bad condition. I guess I will go with the duplicolor bgmo535. thanks

User avatar
ajs350
ICOA Member
ICOA Member
Posts: 327
Joined: Wed Nov 17, 2010 2:19 pm
Location: Atlanta GA USA
Location: Atlanta, GA USA

Re: Painting my valve cover

Post by ajs350 »

I used the dupli color but washed the cover off with Gunk first to remove the oil. The paint does not handle solvents too well. I got carb cleaner on mine and had to paint it again.
Ross
4376

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4737
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: Painting my valve cover

Post by daves79x »

Just a couple of other notes - Dupli-Color is not a 'high temp' paint, but that's mostly a marketing gimmick. You can paint any and all engine parts with it and it holds up great.

Also Jay, you mentioned that you used steel wool in one of your final scrubs. Steel wool contains oil - I would stay away from that.

Nice job guys on the covers!

Dave

steve murdoch icoa #5322
ICOA Member
ICOA Member
Posts: 4068
Joined: Tue Mar 04, 2003 9:12 am
Location: St. Catharines, On. Canada
Location: St. Catharines, On. Canada

Re: Painting my valve cover

Post by steve murdoch icoa #5322 »

Why no clear over the paint?
Does it not take the heat and start to yellow?

User avatar
NobleHops
ICOA Member
ICOA Member
Posts: 3867
Joined: Mon Jan 25, 2010 7:17 am
Location: Tucson, Arizona, USA
Location: Tucson, Arizona, USA

Re: Painting my valve cover

Post by NobleHops »

If I'm not mistaken, it's a bit dicey to install the valve cover with that tacho drive in place. Risk of breaking it as I recall? Am I remembering this correctly?

N.
Nils Menten
Tucson, Arizona, USA '80 CBX, sort-of restored :-)

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4737
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: Painting my valve cover

Post by daves79x »

Yes, Nils, you are correct. I'm assuming it was installed for the photo only?

The Dupli-Color paint used here is not meant to be used with a clearcoat, if I remember correctly, for one thing. However, even using a clearcoat is risky due to yellowing, as Steve said. Not sure what advantage or look you would be trying to achieve with a clearcoat there.

Dave

User avatar
Don
Amazing Poster
Amazing Poster
Posts: 806
Joined: Wed Apr 02, 2003 3:13 pm
Location: Biloxi, Mississippi, USA
Location: Biloxi, Mississippi, USA

Re: Painting my valve cover

Post by Don »

I agree

The clear doesn't stand up to heat/sun/weather nearly as well as the silver paint itself

If you have a local guy who does powdercoating, that's the best solution other than chrome if you want a tough, lasting finish impervious to gas, oil and chemicals. My local guy will do something like a valve cover for $50. I paid $75 for a primer and two coats of satin black powder on my front boomerang wheel to make it match the black anodized rear wheel I bought and it turned out beautiful - No comparing rattle can painting to powdercoating

Don

User avatar
ajs350
ICOA Member
ICOA Member
Posts: 327
Joined: Wed Nov 17, 2010 2:19 pm
Location: Atlanta GA USA
Location: Atlanta, GA USA

Re: Painting my valve cover

Post by ajs350 »

daves79x wrote:Yes, Nils, you are correct. I'm assuming it was installed for the photo only?

Dave
Dave, you are right. I just put the tach drive on for the photo. Ross

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: Painting my valve cover

Post by EMS »

My preference is still polishing. I had two valve covers professionally polished some 10 years ago and they still look great. No clearcoat. Just a little Mother's or Mequire's occasionally.

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4737
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: Painting my valve cover

Post by daves79x »

Mike:
I think these guys were looking to reproduce the stock look for the early models. For late models like yours, polishing would be the more proper finish.

Dave

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: Painting my valve cover

Post by EMS »

daves79x wrote:Mike:
I think these guys were looking to reproduce the stock look for the early models. For late models like yours, polishing would be the more proper finish.

Dave

One of the polished covers is on my '79 :wink: I don't have the desire to have detail-correct show bike, though 8)
838

Black engine with polished valve cover looks positively sinister on that red 79, but for Dog's sake, paint that magnesium alternator cover, willya! :-)

N.

Post Reply

Return to “RESTORATIONS: Tips, How To's & What Not to Do. Parts, Decals, Painters, Paint Codes, Painting Tips.....More”