Page 1 of 1
Special Tool (Steering Stem Socket) 07916-371-0100
Posted: Fri Jul 17, 2009 2:12 pm
by bdento59
Does anyone have photos and/or dimensions for the Honda special tool called "Steering stem socket"? The P/N in the shop manual is 07916-371-0100, but has since been superceded by P/N 07916-371-0101. I found it for sale domestically, but at $54, I'd like to see what it looks like first in case I can fabricate one instead.
As always, TIA
Posted: Fri Jul 17, 2009 2:45 pm
by alimey4u2
I'm trying to get a fellow on E-Bay over here to make two. Hadn't heard from him since I had been on vacation, lemme give him another prompt..
Here are the nuts & info needed...
Posted: Fri Jul 17, 2009 7:06 pm
by alimey4u2
The Gentleman just contacted me again, so we will see where this goes. Normally looking about $30 for each socket... He made me one for the 1980 swinging arm nut which was a jewel..
Tools
Posted: Fri Jul 17, 2009 10:54 pm
by Tom Neimeyer
A few years ago I made some for the steering stem (normal CBX takes two) and for the clutch nut. I sold some on E-Bay and some on club site. Here are a couple I use.
Pretty easy for the average "Shade Tree Mechanic" to make buy a used socket from a Pawn shop for $3 and crank up the Dremel and 2 hours later....poof....you got it.
Cheers, Tom
Posted: Sat Jul 18, 2009 6:09 am
by alimey4u2
I wouldn't call yourself the average "shade tree mechanic" Tom.. Far from it....
I too thought about following your example but I have a shiny tool fetish...
Good stuff...
Re: Tools
Posted: Sun Jul 19, 2009 1:04 am
by bdento59
Tom Neimeyer wrote:A few years ago I made some for the steering stem (normal CBX takes two) and for the clutch nut. I sold some on E-Bay and some on club site. Here are a couple I use.
Hi Tom,
Very nice. The middle one looks familiar, as I already made one of those (clutch nut variety) by your lead in the tech section article in this website. Maybe you could bring the others to VMD and let me borrow them for patterns? Thanks 1KK...
annotated photos
Posted: Sun Jul 19, 2009 1:07 am
by bdento59
alimey4u2 wrote:I'm trying to get a fellow on E-Bay over here to make two. Hadn't heard from him since I had been on vacation, lemme give him another prompt.
Alimey, thanks so much for the beautifully annotated photos! They are very helpful. Lemme know what the E-Bay fellow says...
Re: annotated photos
Posted: Sun Jul 19, 2009 5:12 am
by alimey4u2
bdento59 wrote:alimey4u2 wrote:I'm trying to get a fellow on E-Bay over here to make two. Hadn't heard from him since I had been on vacation, lemme give him another prompt.
Alimey, thanks so much for the beautifully annotated photos! They are very helpful. Lemme know what the E-Bay fellow says...
He contacted me again to finalise so this time it may be a go.... I'll keep ya'll updated...
Posted: Sun Aug 09, 2009 5:28 am
by alimey4u2
Tools are being shipped as we speak, I'll check them out on arrival & post the info....
Posted: Tue Aug 11, 2009 8:11 am
by alimey4u2
Superb fit, 50 Pounds Sterling for both, including shipping within the UK. I can find out how much to the States if you wish ? If you have an another application the gentleman will make the item for you for a discount price. Mine were discounted as I took the time to research & give him drawings. PM me if you are interested & I'll give you the contact info....
Posted: Tue Aug 11, 2009 8:43 am
by Joner
Yep you do have a shiny tool fetish Larry
They do look good though.
Might have to get me some made, I'm still waiting for my mate to finish some bits for me (only had them for 11 months). Can't complain though I told him no rush, and he isn't charging.
Cheers
Chris J.
Posted: Tue Aug 11, 2009 9:06 am
by alimey4u2
Thanks Chris, I'll post the info on UKCBXCLUB as well....
