20 years of....Building the dream......
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
Carbs back together with no more leaks, or sticking float valves, and the accelerator pump is working good too.
Bike fired up very easy, and is now running more evenly on all the cylinders....plugs all look great..... (all running time inside garage)
While running it this time, I found a new problem....the throwout bearing, or pressure plate bearing is making some noise.
Looks like I have to drain the oil, and pull the clutch cover off....
Hopefully my alternator will show up when I get my clutch put back together....then I can try to get my carbs synced.... probably have snow by then though (no road test till April probably)
And I just now realized that the gasket for the clutch is no longer available.....Why....
Bike fired up very easy, and is now running more evenly on all the cylinders....plugs all look great..... (all running time inside garage)
While running it this time, I found a new problem....the throwout bearing, or pressure plate bearing is making some noise.
Looks like I have to drain the oil, and pull the clutch cover off....
Hopefully my alternator will show up when I get my clutch put back together....then I can try to get my carbs synced.... probably have snow by then though (no road test till April probably)
And I just now realized that the gasket for the clutch is no longer available.....Why....
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
-
- ICOA Technical Director
- Posts: 4787
- Joined: Sun Oct 01, 2006 8:05 am
- Location: Knox, PA
- Location: Knox, PA
Re: 20 years of....Building the dream......
TIMS has just about all the engine gaskets available separately. Yes, Honda is running out of even wear parts like gaskets and seals for the CBX, but diligent searching here and overseas will turn up everything. Bill at TIMS, Louis, David Silver, Six Center and others.
Why do you think the clutch bearing is bad? Never saw one fail, but have heard hundreds of noisy '79 clutch baskets. Don't think the bearing is your problem.
Great news on the carbs!
Dave
Why do you think the clutch bearing is bad? Never saw one fail, but have heard hundreds of noisy '79 clutch baskets. Don't think the bearing is your problem.
Great news on the carbs!
Dave
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
I pulled the cable off, and the noise stopped...I pulled up on the lever on the housing and could then hear it, and feel it in the lever.
I had taped the hand lever to the handlebar grip, while trying to get the bike first running (wired in a clutch saftey from the F3 controls...). I'm guessing the constant pressure on the bearing, with no oil to it for years...then firing it up, might have hurt it that way..........?
I had taped the hand lever to the handlebar grip, while trying to get the bike first running (wired in a clutch saftey from the F3 controls...). I'm guessing the constant pressure on the bearing, with no oil to it for years...then firing it up, might have hurt it that way..........?
Last edited by cbxtreeme on Thu Dec 24, 2015 7:42 pm, edited 1 time in total.
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
My girlfriend just gave me one of my Christmas presents today....
A pair of the best tires Bridgestone has created yet....!!!! The RS10
These things will wear holes in my pipes and crank covers for sure...
The Michelin High Sports on the bike now were the top choice in the 90's, but not safe in my mind at their age now... I might still have some rubber soft enough to do a good smoky burnout though...
A pair of the best tires Bridgestone has created yet....!!!! The RS10
These things will wear holes in my pipes and crank covers for sure...
The Michelin High Sports on the bike now were the top choice in the 90's, but not safe in my mind at their age now... I might still have some rubber soft enough to do a good smoky burnout though...
You do not have the required permissions to view the files attached to this post.
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
-
- ICOA Member
- Posts: 4082
- Joined: Tue Mar 04, 2003 9:12 am
- Location: St. Catharines, On. Canada
- Location: St. Catharines, On. Canada
Re: 20 years of....Building the dream......
With those tires we better see some pics from the track.
Very nice.
Very nice.
-
- ICOA Technical Director
- Posts: 4787
- Joined: Sun Oct 01, 2006 8:05 am
- Location: Knox, PA
- Location: Knox, PA
Re: 20 years of....Building the dream......
Funny how she knew the exact type and size of tire to get!
Dave
Dave
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
Well.....she did ask for a list....
I'll probably get some pics of it in action on a dyno....but it's a pretty big beast for track days.
Planning on a few next year on my RS250, that's been collecting dust for too long.
If I survive that I might take it to the track, where someone there might get a pic or two....
Merry Christmas to all.............
I'll probably get some pics of it in action on a dyno....but it's a pretty big beast for track days.
Planning on a few next year on my RS250, that's been collecting dust for too long.
If I survive that I might take it to the track, where someone there might get a pic or two....
Merry Christmas to all.............
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
Just back from Corpus Christie long enough to pick this up from post office, before I head to Niagara Falls.
Well... It won't be done before New Years.... But I'll have my clutch parts by the time I'm back...
Well... It won't be done before New Years.... But I'll have my clutch parts by the time I'm back...
You do not have the required permissions to view the files attached to this post.
Last edited by cbxtreeme on Sat Jan 02, 2016 9:44 pm, edited 1 time in total.
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
- NobleHops
- ICOA Member
- Posts: 3885
- Joined: Mon Jan 25, 2010 7:17 am
- Location: Tucson, Arizona, USA
- Location: Tucson, Arizona, USA
Re: 20 years of....Building the dream......
Great part, you're going to love it. Looking good!
Nils Menten
Tucson, Arizona, USA '80 CBX, sort-of restored :-)
Tucson, Arizona, USA '80 CBX, sort-of restored :-)
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
Finally had time today to swap out the alternator and test it.
The cheap silver paint that was sprayed on it, was smudging with oil and gas on my hands.
So I pulled it apart and soda blasted the housing, and polished it up just a bit.
Pulled my old parts off and plugged in the new wires with ease. Put some gas in the carbs and fired right up...
And it was charging.....!!!!
One more issue out of the way....now I need to get clutch straightened out and tires on... Then pray for a short winter.
The cheap silver paint that was sprayed on it, was smudging with oil and gas on my hands.
So I pulled it apart and soda blasted the housing, and polished it up just a bit.
Pulled my old parts off and plugged in the new wires with ease. Put some gas in the carbs and fired right up...
And it was charging.....!!!!
One more issue out of the way....now I need to get clutch straightened out and tires on... Then pray for a short winter.
You do not have the required permissions to view the files attached to this post.
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
-
- ICOA Member
- Posts: 569
- Joined: Fri Jun 12, 2015 9:56 am
- Location: Canmore Alberta Canada
- Location: Canmore Alberta Canada
Re: 20 years of....Building the dream......
Yellow plug wires? Where did you get yellow plug wires?
All I can find is blue,orange,black and red but not yellow in 8mm.
Plus, Is that a NOS bottle hiding in there?
OH I know, its part of the foot activated air pump for maintaining tire pressure.
Just kidding. Although, a NOS sticker on that air shifter bottle will fool a lot of people.
All I can find is blue,orange,black and red but not yellow in 8mm.
Plus, Is that a NOS bottle hiding in there?
OH I know, its part of the foot activated air pump for maintaining tire pressure.
Just kidding. Although, a NOS sticker on that air shifter bottle will fool a lot of people.
Canadian Amateur Radio Call sign VE6 VES
-
- ICOA Member
- Posts: 4082
- Joined: Tue Mar 04, 2003 9:12 am
- Location: St. Catharines, On. Canada
- Location: St. Catharines, On. Canada
Re: 20 years of....Building the dream......
Mouse, Accel makes an 8mm yellow plug wire.
I think Canadian Tire may even carry them. If not any hot rod car shop should be able to get them.
I think Canadian Tire may even carry them. If not any hot rod car shop should be able to get them.
- wyly
- ICOA Member
- Posts: 1733
- Joined: Tue Oct 30, 2007 4:20 pm
- Location: calgary alberta canada
- Location: Calgary Canada
Re: 20 years of....Building the dream......
Accel like Steve mentioned or from Taylor http://www.taylorvertex.com/spark-plugs ... wire-sets/ that's where I found my orange wire set.Mouse wrote:Yellow plug wires? Where did you get yellow plug wires?
All I can find is blue,orange,black and red but not yellow in 8mm.
Plus, Is that a NOS bottle hiding in there?
OH I know, its part of the foot activated air pump for maintaining tire pressure.
Just kidding. Although, a NOS sticker on that air shifter bottle will fool a lot of people.
Next time you come down from those mountains and back to civilization you may find them in stock at Mopac Auto Supply on 16th ave N/W...
CBX a work in progress, still improving...GS1150EFE completed and awaiting modifications.....RD350, remnants in boxes scattered throughout the garage
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
Yep....got them with my coils
Although I have Dyna ignition to go along with the coils...
Although I have Dyna ignition to go along with the coils...
You do not have the required permissions to view the files attached to this post.
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
-
- Forum Regular
- Posts: 97
- Joined: Wed Nov 11, 2015 8:58 pm
- Location: Indiana
- Location: Indiana
Re: 20 years of....Building the dream......
Pulled clutch apart today and found my issues that I had suspected.
Bearing does not roll perfectly smooth with side load pressure...and I also noticed that my heavy duty springs are rubbing/digging in the posts that hold them in. Coils are catching and leave an notchy/dragging feel.
Need to slightly grind inside of the coils to get better clearance.
Bearing does not roll perfectly smooth with side load pressure...and I also noticed that my heavy duty springs are rubbing/digging in the posts that hold them in. Coils are catching and leave an notchy/dragging feel.
Need to slightly grind inside of the coils to get better clearance.
You do not have the required permissions to view the files attached to this post.
___________MY TWO STROKE ADDICTION_____________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________
RGV VJ21 L___________________RZ 350_____________
RGV VJ22 FL__________ GT 750 long term cafe project___
RGV VJ22 N ________________RS 250 Cup Bike_________
RGV VJ23 T__________And one for the water...SX-R 800_
____________________RZV500R______________________