CBX 1000Z Restoration - Candy Glory Red this time!

Hey, what projects are you planning or preparing for? CBX, other motos, workshop, WHATEVAH!
jnnngs
ICOA Member
ICOA Member
Posts: 420
Joined: Tue Feb 10, 2015 2:05 pm
Location: Hants/UK
Location: Hants/UK

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by jnnngs »

Instrument Cluster

As the original clocks were faded, I decided to spruce them up somewhat.

I started off using these decals:

http://www.ebay.co.uk/itm/Honda-CBX1000 ... Sw7NNUBvyK

These are "stickers" which you apply to your existing clock plates. The process is you sand down the plates to remove the existing paint, and to get back to the original orange plates. Depending on how faded your plates are, you have to sand away quite a lot of the plate - a few mm so the plate does get significantly thinner.

Starting point:
DSC05474.JPG
After removing black paint to reveal faded underlying plate:
DSC05475.JPG
After sanding until all faded orange is removed and the decal before applying to the plate:
DSC05478.JPG
After applying the decal:
DSC05485.JPG
The finish was OK but decided to compare it to the clock plates sold by Pete Rose (DigitalPizza). Pete's plates are on the bottom:
DSC05528.JPG
I decided to go with Pete's plates in the end - just personal choice, nothing against the other decals!

Pete's plates are a little thicker than the originals, and the backs are not painted (the originals are painted silver including the cut outs in the speedo). I decided to paint mine silver - as per original:
20151211_094827.jpg
20151215_132642.jpg
A few other observations:
- As Petes' plates are a little thicker, one of the needles was rubbing the surface of the new plate - I had to remove a little from the back of the needle (there's a heat weld on the back which I needed to trim)
- I also got my "idiot lights" re-lettered by Pete (well worth doing).
- I painted the clock bezels before re-crimping them. In the end, I damaged the paint (slightly) while re-crimping, so had to paint them again.
- Having got nice new orange plates, the needles look very faded - you really need to paint that aswell. I used modellers paint (Fluorescent Red) which was a good match.
- The screws holding the face plates on are pretty tight - you need a really good fitting screwdriver to get them out. I destroyed one of mine - thanks to Pete for providing a replacement.

Repainting the bezels:
20151218_091524.jpg
Painted Needle:
20151116_154117.jpg
Here's the finished result:
20151223_164101.jpg
Well worth the effort / cost of doing it in my opinion.

(My thanks to Pete for helping me with this along the way)

Paul.
You do not have the required permissions to view the files attached to this post.

jnnngs
ICOA Member
ICOA Member
Posts: 420
Joined: Tue Feb 10, 2015 2:05 pm
Location: Hants/UK
Location: Hants/UK

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by jnnngs »

Merry Xmas

Not quite finished, but almost there:
20151223_141239.jpg
I have finished until after Xmas.

Merry Xmas to you all.

Paul.
You do not have the required permissions to view the files attached to this post.

User avatar
NobleHops
ICOA Member
ICOA Member
Posts: 3867
Joined: Mon Jan 25, 2010 7:17 am
Location: Tucson, Arizona, USA
Location: Tucson, Arizona, USA

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by NobleHops »

Bravo! Merry Christmas to you as well!
Nils Menten
Tucson, Arizona, USA '80 CBX, sort-of restored :-)

steve murdoch icoa #5322
ICOA Member
ICOA Member
Posts: 4069
Joined: Tue Mar 04, 2003 9:12 am
Location: St. Catharines, On. Canada
Location: St. Catharines, On. Canada

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by steve murdoch icoa #5322 »

Very nice work, Paul and thanks for the write-up.

jnnngs
ICOA Member
ICOA Member
Posts: 420
Joined: Tue Feb 10, 2015 2:05 pm
Location: Hants/UK
Location: Hants/UK

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by jnnngs »

Hi,

I have '79 carbs and a later '81/'82 cylinder head.

Question is what carb rubbers should I use between the head and carbs? Does it make a difference in using the '79 rubbers or the later / different '81 rubbers?

I have a leak at the moment, and not sure if I need to replace the rubbers, or if it's a result of having the wrong type fitted (it's got '79 rubbers on at the moment)

thanks,

Paul.

User avatar
FalldownPhil
ICOA Member
ICOA Member
Posts: 929
Joined: Fri Feb 10, 2006 11:25 pm
Location: Marina Del Rey, CA. USA
Contact:

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by FalldownPhil »

The carbs are all the same externally. The '79 insulators should be correct.
Best,
Phil
When you are up to your ass in alligators it is sometimes difficult
to remember that your objective was to drain the swamp !!

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by EMS »

Well, it depends what airbox you are using. The carb rubber boots are different because of the airbox. If you use a 79/80 airbox, use 79/80 rubbers. If you use a 81/82 airbox , use 81/82 rubbers.
On the 81/82 models Honda changed the airflow to a more horizontal level. As a result, the manifold rubbers are ever so slightly "wedge" shaped in order to drop the carbs down at the rear.
Consequently, the openings in the airbox, that receive the carbs are slightly lower.
There are many, who ignore this and mix and match. And I guess, if you don't bother and apply a little more force than you usually have to when something fits nicely, it will work.

User avatar
FalldownPhil
ICOA Member
ICOA Member
Posts: 929
Joined: Fri Feb 10, 2006 11:25 pm
Location: Marina Del Rey, CA. USA
Contact:

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by FalldownPhil »

Thanks Mike !!
Best,
Phil
When you are up to your ass in alligators it is sometimes difficult
to remember that your objective was to drain the swamp !!

jnnngs
ICOA Member
ICOA Member
Posts: 420
Joined: Tue Feb 10, 2015 2:05 pm
Location: Hants/UK
Location: Hants/UK

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by jnnngs »

EMS wrote:Well, it depends what airbox you are using. The carb rubber boots are different because of the airbox. If you use a 79/80 airbox, use 79/80 rubbers. If you use a 81/82 airbox , use 81/82 rubbers.
On the 81/82 models Honda changed the airflow to a more horizontal level. As a result, the manifold rubbers are ever so slightly "wedge" shaped in order to drop the carbs down at the rear.
Consequently, the openings in the airbox, that receive the carbs are slightly lower.
There are many, who ignore this and mix and match. And I guess, if you don't bother and apply a little more force than you usually have to when something fits nicely, it will work.
OK - that helps a lot. I was pretty sure that the carbs were identical externally, so had thought that maybe the cylinder head had been changed a little and as a result needed the different rubbers.

I have stock '79 airbox, so '79 rubbers it is.

Paul.

User avatar
Jeff Bennetts
Posting God
Posting God
Posts: 2408
Joined: Wed Mar 05, 2003 8:38 am
Location: Ohio, USA
Location: Ohio, USA

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by Jeff Bennetts »

FalldownPhil wrote:The carbs are all the same externally. The '79 insulators should be correct.
Best,
Phil
What Phil said, you always match the intake rubbers to whatever year the airbox assembly is from, the head and carb dimensions are the same across the years.

jnnngs
ICOA Member
ICOA Member
Posts: 420
Joined: Tue Feb 10, 2015 2:05 pm
Location: Hants/UK
Location: Hants/UK

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by jnnngs »

Finished

Just to finish off this thread.

Bike now finished:
- fixed cam cover oil leak - changed to an original Honda gasket (the previous one was a new one from an aftermarket gasket kit) and used new rubbers in the end.
- Leak on carb connecting rubbers sorted - just reseated / tightened everything up.

A few pictures:
DSC05533.JPG
DSC05534.JPG
20160106_132430.jpg
DSC05535.JPG
I briefly had a matching pair:
DSC05551.JPG
DSC05547.JPG
Both of the bikes are now sold. This will fund my next restorations - another 1000Z, and just for a change have a Z1A to do:
20160116_164209.jpg

Paul.
You do not have the required permissions to view the files attached to this post.

User avatar
FalldownPhil
ICOA Member
ICOA Member
Posts: 929
Joined: Fri Feb 10, 2006 11:25 pm
Location: Marina Del Rey, CA. USA
Contact:

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by FalldownPhil »

Stunning !!
Best,
Phil
When you are up to your ass in alligators it is sometimes difficult
to remember that your objective was to drain the swamp !!

User avatar
NobleHops
ICOA Member
ICOA Member
Posts: 3867
Joined: Mon Jan 25, 2010 7:17 am
Location: Tucson, Arizona, USA
Location: Tucson, Arizona, USA

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by NobleHops »

Tremendous project, great content for everyone to enjoy. Thank you so much for sharing this with us Paul, great job.
Nils Menten
Tucson, Arizona, USA '80 CBX, sort-of restored :-)

steve murdoch icoa #5322
ICOA Member
ICOA Member
Posts: 4069
Joined: Tue Mar 04, 2003 9:12 am
Location: St. Catharines, On. Canada
Location: St. Catharines, On. Canada

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by steve murdoch icoa #5322 »

Excellent work, Paul.
From afar it doesn't look like the next one needs much but it would be great if you did a thread on that resto as well.
We always seem to learn a couple things from each project.

jnnngs
ICOA Member
ICOA Member
Posts: 420
Joined: Tue Feb 10, 2015 2:05 pm
Location: Hants/UK
Location: Hants/UK

Re: CBX 1000Z Restoration - Candy Glory Red this time!

Post by jnnngs »

steve murdoch icoa #5322 wrote:Excellent work, Paul.
From afar it doesn't look like the next one needs much but it would be great if you did a thread on that resto as well.
We always seem to learn a couple things from each project.
The silver Z is a UK bike - been off the road for 15 years and doesn't run (just the carbs I think). It's pretty complete / original, not sure whether I will do a full restoration, or just get it running as a usable bike. Will take a closer look at this week.

I am also looking at another UK Z tomorrow (a red one), carbs need doing (as always) but told is otherwise OK. Assuming it as they say it is, will probably get that one.

Is it a just a hobby or more an addiction...difficult to tell the difference!

Paul.

Post Reply

Return to “Project Threads”