Non abrasive cleaning

Post Reply
User avatar
Kool_Biker
ICOA Member
ICOA Member
Posts: 654
Joined: Sat Dec 18, 2010 5:46 pm
Location: Great Britain
Location: Great Britain

Non abrasive cleaning

Post by Kool_Biker »

What's the best way to clean brake parts NON ABRASIVELY?
Surely one can go in with a (soft) brush, but there must be a better way to get rid of most of the surface dirt and oxidation, before a final polish?
P1100844.jpg
Cheers, Aris
You do not have the required permissions to view the files attached to this post.
Aris Hadjiaslanis
ICOA # 6309
Berkshire, Windsor

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: Non abrasive cleaning

Post by EMS »

I use spray-on brake cleaner and a soft nylon or brass brush. Then I also have a commercial parts washer at my disposal, that cleans with 175°F solvent.

User avatar
Kool_Biker
ICOA Member
ICOA Member
Posts: 654
Joined: Sat Dec 18, 2010 5:46 pm
Location: Great Britain
Location: Great Britain

Re: Non abrasive cleaning

Post by Kool_Biker »

Mike, thanks.
My room temperature parts washers and lots of elbow grease with hard nylon brushes did the job in the end.
But could you pls tell us more about your hi temp parts washer. May be a manufacturer's link and a bit about your experience.
Sounds interesting ...
Aris
Aris Hadjiaslanis
ICOA # 6309
Berkshire, Windsor

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: Non abrasive cleaning

Post by EMS »

Kool_Biker wrote:Mike, thanks.
But could you pls tell us more about your hi temp parts washer. May be a manufacturer's link and a bit about your experience.
Sounds interesting ...
Aris
8) 8) Aris: It is a $15,000 commercial parts washer we have at the company ;-)

User avatar
Kool_Biker
ICOA Member
ICOA Member
Posts: 654
Joined: Sat Dec 18, 2010 5:46 pm
Location: Great Britain
Location: Great Britain

Re: Non abrasive cleaning

Post by Kool_Biker »

So?
I'm planning to buy two (in case I break one) ...

But seriously Mike, some people seem to have all the luck !!!

Aris :lol:
Aris Hadjiaslanis
ICOA # 6309
Berkshire, Windsor

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: Non abrasive cleaning

Post by EMS »

Here you go, Aris. It is considered a "small to medium size" unit manufactured by JRI in Springfield, MO. Distributed by SafetyKleen.
It connects to 460Volt 3-phase. The baskets can be removed. If I remove the upper, I can wash a complete CBX engine in there.
It comes in handy, if you have to remove paint from a large part. Spray it with paint stripper and then put it in the washer for 30 minuets and it comes out spanky clean.
The solvent in the washing fluid may leave a residue when you let it dry, so you should flush the part with clean water.


5078

User avatar
BiPolarBear
New Member & Happy To Be Here
New Member & Happy To Be Here
Posts: 19
Joined: Mon Apr 30, 2012 10:00 pm
Location: Louisville, KY
Location: Louisville, KY

Re: Non abrasive cleaning

Post by BiPolarBear »

Now I KNOW I'm a sick puppy. It may be that I'm just middle-aged, and losing the passion of youth, but industrial level tools like that make my nipples hard. If I hit the lottery, I'm getting one....
BearWing
Nasty, Brutish, and Short

1967 Yamaha U5-E
1971 Honda CB175 Candy Gold
1972 Norton Commando 750
1973 Honda CB350F Candy Bacchus Olive
1975 Suzuki GT750M Jewel Grey
1975 Honda GL1000 Candy Blue Green
1976 Honda GL1000 Sulfur Yellow
1976 Benelli Sei
1979 Honda CBX Glory Red
1983 Honda CB1100F

You are NEVER too old for a happy childhood!

User avatar
Jeff Bennetts
Posting God
Posting God
Posts: 2408
Joined: Wed Mar 05, 2003 8:38 am
Location: Ohio, USA
Location: Ohio, USA

Re: Non abrasive cleaning

Post by Jeff Bennetts »

BiPolarBear wrote:Now I KNOW I'm a sick puppy. It may be that I'm just middle-aged, and losing the passion of youth, but industrial level tools like that make my nipples hard. If I hit the lottery, I'm getting one....
Diamond hard or just rock hard?

barryadam
ICOA Member
ICOA Member
Posts: 283
Joined: Thu Oct 15, 2009 12:33 am
Location: Mission Viejo, California, USA
Location: Mission Viejo, California, USA

Re: Non abrasive cleaning

Post by barryadam »

Kool_Biker wrote:What's the best way to clean brake parts NON ABRASIVELY?
Surely one can go in with a (soft) brush, but there must be a better way to get rid of most of the surface dirt and oxidation, before a final polish?
Cheers, Aris
Aris,

My project '79 CBX rear master cylinder looks WORSE than yours. I'll post pics when it's done, but basically, I did the carb dip, chemical strip, and solvent clean, ultrasonic, then I used my blast cabinet with 0000 glass beads (basically powder, like soda), and reduced air pressure (50 -60 psi) to clean up the corroded aluminum. The glass beads do not "cut", and being so fine, and with little air pressure, they don't even peen the surface like normal bead blasting would. Just lightly clean.
I make small wheels for the Dremel using punch-outs from extra-fine scotchbrite disks, and ran that lightly in the end of the bore that had some corrosion. I measured to verify the plunger seal will be located in a clean part of the bore when at rest.

My next step is to have the m/c anodized. I have some Honda VF1000R front calipers that are not painted, and the piston bores are like new because of the anodize treatment. It seems to hold up really well against the typical white crust deposits/corrosion in the brake systems. I'm having the rear caliper done, as well.

After anodizing the rear master cylinder and caliper, I'll have the exterior powder coated, and they will look like the original.

And, yes, I've gaged the tiny pressure relief hole so that I can ensure it is the exact same size when I'm done.

Barry
Last edited by barryadam on Fri Aug 03, 2012 1:31 pm, edited 1 time in total.

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: Non abrasive cleaning

Post by EMS »

barryadam wrote: My next step is to have the m/c anodized. Barry
Barry: Apply care when you anodize the bore. The diameter will change and the proper fit of the piston and seals must be verified.

barryadam
ICOA Member
ICOA Member
Posts: 283
Joined: Thu Oct 15, 2009 12:33 am
Location: Mission Viejo, California, USA
Location: Mission Viejo, California, USA

Re: Non abrasive cleaning

Post by barryadam »

EMS wrote: Barry: Apply care when you anodize the bore. The diameter will change and the proper fit of the piston and seals must be verified.
Will do, Mike.
Thanks.

Post Reply

Return to “BRAKES: Calipers, Pads, Lines, Rotors, Upgrades & Fixes”