VF1000R rear wheel?

Post Reply
droptail
Forum Regular
Forum Regular
Posts: 56
Joined: Sun Mar 18, 2007 12:20 pm
Location: SoCal
Contact:

VF1000R rear wheel?

Post by droptail »

vfr.rr.wh.cbx.gif
I finally got around to swapping in the wider rear VF1000R wheel and brake with the nice 160 tire. I have discovered a wobble and found the rim isn't true. What are the fasteners called that secure the wheel spars? And can anyone offhand direct me to a wheel true article?

Thanks
You do not have the required permissions to view the files attached to this post.
'80 CBX '81 CBX '83 GS1100ES '84 GPZ1100 '04 FJR1300 '00 GSX1300R

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4736
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: VF1000R rear wheel?

Post by daves79x »

Try these folks - they do excellent work. http://www.framestraightsystem.com/

Dave

droptail
Forum Regular
Forum Regular
Posts: 56
Joined: Sun Mar 18, 2007 12:20 pm
Location: SoCal
Contact:

Re: VF1000R rear wheel?

Post by droptail »

Thanks for the quick reply. I will contact if I am not able to straighten it out myself. I am hoping I can do it through adjusting the spar fasteners, after I figure out what type of head they are (it was too dark last night to see the details).
'80 CBX '81 CBX '83 GS1100ES '84 GPZ1100 '04 FJR1300 '00 GSX1300R

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4736
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: VF1000R rear wheel?

Post by daves79x »

The wheel is probably not meant to be 'fiddled' with that way. But proceed however you see fit.

Dave

User avatar
NobleHops
ICOA Member
ICOA Member
Posts: 3867
Joined: Mon Jan 25, 2010 7:17 am
Location: Tucson, Arizona, USA
Location: Tucson, Arizona, USA

Re: VF1000R rear wheel?

Post by NobleHops »

Yeah, put a bit blunter, no way. That's not like a spoke you're going to be able to tighten to true. I'd eat it and send it out, lest you overtorque and snap one of those fasteners trying to add or subtract tension. Those are small fasteners and likely not up to a lot of additional torque on an experimental basis and there's no way those are going to be useful in truing that wheel, IMO.

N.
Nils Menten
Tucson, Arizona, USA '80 CBX, sort-of restored :-)

EMS
ICOA Member
ICOA Member
Posts: 10151
Joined: Wed Mar 05, 2003 7:55 am
Location: North East OH, ICOA 3904

Re: VF1000R rear wheel?

Post by EMS »

I was going to make a suggestion...but I am stretched a little too thin on this board! 8)

steve murdoch icoa #5322
ICOA Member
ICOA Member
Posts: 4068
Joined: Tue Mar 04, 2003 9:12 am
Location: St. Catharines, On. Canada
Location: St. Catharines, On. Canada

Re: VF1000R rear wheel?

Post by steve murdoch icoa #5322 »

Isn't a 160 tire too big for that rim or has it been widened.
I would have thought the stock size was 130, 140 tops.
Could that be causing the wobble?
Never seen drilled Prolink rotors. I like the look.

droptail
Forum Regular
Forum Regular
Posts: 56
Joined: Sun Mar 18, 2007 12:20 pm
Location: SoCal
Contact:

Re: VF1000R rear wheel?

Post by droptail »

Before I do anything, I'm going to verify the torque of all the fasteners. Then remove them all and check the rim. Then, once I know where the problem lies, I will proceed. I had no intentions of over torquing and shearing anything. Thats not how I roll (usually).

Of coarse I was warned emphatically to not cross drill my rotors, that they would crack, break, and cause a crash (about 15 years ago). They have worked good, and look great IMO.

Thanks for the replys and warnings.
'80 CBX '81 CBX '83 GS1100ES '84 GPZ1100 '04 FJR1300 '00 GSX1300R

User avatar
NobleHops
ICOA Member
ICOA Member
Posts: 3867
Joined: Mon Jan 25, 2010 7:17 am
Location: Tucson, Arizona, USA
Location: Tucson, Arizona, USA

Re: VF1000R rear wheel?

Post by NobleHops »

What's your theory, just because I'm curious? Those fasteners are 90 degrees to the axis of the wheel. What do you hope to happen when you tighten or loosen them?

N.
Nils Menten
Tucson, Arizona, USA '80 CBX, sort-of restored :-)

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4736
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: VF1000R rear wheel?

Post by daves79x »

To 'pile on' with Nils, unless those are really unique Honda wheels, none I know of were designed to be taken apart. They usually have special kinds of bolts/nuts that ordinary wrenches don't fit anyway. My guess is that if yours has conventional fasteners, then someone before you was fiddling. Let us know what you find.

Dave

droptail
Forum Regular
Forum Regular
Posts: 56
Joined: Sun Mar 18, 2007 12:20 pm
Location: SoCal
Contact:

Re: VF1000R rear wheel?

Post by droptail »

I saw what appears to be a composite assembly using threaded fasteners so I intended to check it out.

My plan is to disassemble, compare the spars for irregularities, and check the rim without influencing support structure. Then compare eccentricity of rim, assembled and assembled to determine cause and location. Assess serviceability.
Nils: the spars are not perpendicular to the rim. That would make for an unsupported structure at its intended service loading.
Dave: the fasteners aren't conventional, hence my question about what they're called.
Now, with my glasses on, a close inspection appears to indicate fasteners are one way use.

It does sound problematic at this point so I'm pursuing alternative options. I'll post if I discover something.

Thanks for the interest.
'80 CBX '81 CBX '83 GS1100ES '84 GPZ1100 '04 FJR1300 '00 GSX1300R

User avatar
Don
Amazing Poster
Amazing Poster
Posts: 806
Joined: Wed Apr 02, 2003 3:13 pm
Location: Biloxi, Mississippi, USA
Location: Biloxi, Mississippi, USA

Re: VF1000R rear wheel?

Post by Don »

My VF1000F rear wheel ('83) uses triangular nuts and bolts and it has "Do Not Disassemble" stamped into the metal in half a dozen places

Don

Post Reply

Return to “TIRES & RIMS: Tire Brands, Mileage, Performance, Sizes, Interchangeability with other models”