Tires for my `82
- Highmileage
- Forum Regular
- Posts: 188
- Joined: Sun Dec 28, 2008 9:54 pm
- Location: Lower Slower Delaware, USA
- Location: Lower Slower Delaware, USA
Dunlops that are offered as original equipment are usually quite different than the ones that we are most likely to buy.
Note: I did not use the word 'any' in the above sentence.
I like the Dunlop Elite 3's that I have on my Suzuki GS 1000 GL. Although not inexpensive, they've lasted a really long time.
But for my '82 CBX (which is due for a change of rubber), I am about to order a set of the S-11's.
Note: I did not use the word 'any' in the above sentence.
I like the Dunlop Elite 3's that I have on my Suzuki GS 1000 GL. Although not inexpensive, they've lasted a really long time.
But for my '82 CBX (which is due for a change of rubber), I am about to order a set of the S-11's.
-
- ICOA Member
- Posts: 10151
- Joined: Wed Mar 05, 2003 7:55 am
- Location: North East OH, ICOA 3904
-
- ICOA Member
- Posts: 2306
- Joined: Thu Jan 30, 2003 9:45 pm
- Location: norcal
- Location: Northern California, USA
I think its pretty standard Mike for manufacturers to install 'standard' type OE tires for all vehicles that aren't performance related. A Ford Taurus will have less than spectacular rubber than say a Shelby Mustang. Same with motorcycles. Even the Hayabusa comes with Brickstone tires that everyone changes out ASAP because they don't stick very well or otherwise don't handle as well as other 'aftermarket' tires do. (Those) kind of tires are far cheaper for the manufacturers than high spec rubber. Same goes with shocks. Ever look at an OEM shock absorber compared to aftermarket shocks?EMS wrote:Why would that be Can you elaborate on this? Inquiring minds want to know.Highmileage wrote:Dunlops that are offered as original equipment are usually quite different than the ones that we are most likely to buy.
.
It ain't the destination, its the journey...
-
- ICOA Member
- Posts: 10151
- Joined: Wed Mar 05, 2003 7:55 am
- Location: North East OH, ICOA 3904
Well, I work in the automotive supplier industry and we are selling the same product to the OEM as we sell to the OEM- and independent aftermarket. I would think that this is common practice. I just can't see that a supplier would make two different quality products of the same part. Most OEMs are getting their OEM replacement parts through the same supply channels as their production parts.
For products like tires, brake pads, clutches etc, which are "wear parts", the aftermarket quantities are significantly higher than the OEM numbers which would make it not very economic to make a more expensive part than for the lower quantity OEM business.
As far as tires go, the only difference I can see is the age. All tires should actually sit a little after they are being made. If the just-in-time process gets them too quick on a vehicle and after that too quick on the road, the fresh rubber may wear prematurely. But that is really splitting hairs.
You guys really think, that Dunlop makes a 501 with "Harley-Davidson" molded on them for the factory, one with a different rubber mix for the dealers and again a different one (or two) for non-Harley applications? You're kidding, right?
For products like tires, brake pads, clutches etc, which are "wear parts", the aftermarket quantities are significantly higher than the OEM numbers which would make it not very economic to make a more expensive part than for the lower quantity OEM business.
As far as tires go, the only difference I can see is the age. All tires should actually sit a little after they are being made. If the just-in-time process gets them too quick on a vehicle and after that too quick on the road, the fresh rubber may wear prematurely. But that is really splitting hairs.
You guys really think, that Dunlop makes a 501 with "Harley-Davidson" molded on them for the factory, one with a different rubber mix for the dealers and again a different one (or two) for non-Harley applications? You're kidding, right?
-
- ICOA Member
- Posts: 2306
- Joined: Thu Jan 30, 2003 9:45 pm
- Location: norcal
- Location: Northern California, USA
- Highmileage
- Forum Regular
- Posts: 188
- Joined: Sun Dec 28, 2008 9:54 pm
- Location: Lower Slower Delaware, USA
- Location: Lower Slower Delaware, USA
It's been 25 years since I bought a new bike and I am not up on the tires that come with the latest new bikes.
But on that Honda V-four Sabre, the Dunlops that came with them were not ones that you'd have heard of - they were hard and handled like crud and lasted way too long.
I've seen this with many other bikes - I know that this is how it used to be, but it may or may not be how it still is. To get the OEM Dunlops, you would be better off going through the bike dealer's parts department. The manufacturer specifies the tires that they put on the new bikes.
But unless you were trying to keep it looking like it just came from the showroom, this would be stupid - the tires that most of us are familiar with are far superior to the OEM rubber.
Maybe the bike manufacturers finally realized that we've figured this out. As I said, I'm not sure what tires come on new bikes these days.
Harley has come a long way (tire-wise) since they made their deal with Dunlop. They tires are much improved over what they used to use, and they say 'Harley-Davidson' on the sidewall so the owner will go back to the dealer to buy replacement tires instead of buying generic Dunlops like we would.
I still don't understand the product loyalty that makes H-D riders want the company's logo on practically everything they own...
However, Buells come with Pirellis.
But on that Honda V-four Sabre, the Dunlops that came with them were not ones that you'd have heard of - they were hard and handled like crud and lasted way too long.
I've seen this with many other bikes - I know that this is how it used to be, but it may or may not be how it still is. To get the OEM Dunlops, you would be better off going through the bike dealer's parts department. The manufacturer specifies the tires that they put on the new bikes.
But unless you were trying to keep it looking like it just came from the showroom, this would be stupid - the tires that most of us are familiar with are far superior to the OEM rubber.
Maybe the bike manufacturers finally realized that we've figured this out. As I said, I'm not sure what tires come on new bikes these days.
Harley has come a long way (tire-wise) since they made their deal with Dunlop. They tires are much improved over what they used to use, and they say 'Harley-Davidson' on the sidewall so the owner will go back to the dealer to buy replacement tires instead of buying generic Dunlops like we would.
I still don't understand the product loyalty that makes H-D riders want the company's logo on practically everything they own...
However, Buells come with Pirellis.
- alimey4u2
- ICOA Web Video Director
- Posts: 5093
- Joined: Fri Aug 11, 2006 1:03 pm
- Location: Uphill, WsM, United Kingdom
I remember the early daze, when you bought a Japanese bike the first thing you would do would be to dump the Bridgestones & put Brit rubber & shocks on....
Then you had to put the engine in an Italian /Swiss/Brit/German chassis to handle... Now they all ride better than most street riders can ever hope to achieve...
Then you had to put the engine in an Italian /Swiss/Brit/German chassis to handle... Now they all ride better than most street riders can ever hope to achieve...
ICOA # 656
-
- ICOA Rally Director
- Posts: 2279
- Joined: Wed Sep 03, 2003 3:16 pm
- Location: Lawrencburg, IN
- Location: Lawrenceburg, Indiana
Ohhhh!!! You bring back memories. I had a K81 on the front of my CB750, and a Nankang 5.20x18 on the rear. Same tread pattern and as wide as would fit inside the swingarm. Side wall was about 8" tall.
Handling? All I wanted was the "look". Same as so many squids today.
Handling? All I wanted was the "look". Same as so many squids today.
Rick Pope
Either garage is too small or we have too many bikes. Or Momma's car needs to go outside.
Either garage is too small or we have too many bikes. Or Momma's car needs to go outside.
-
- ICOA Member
- Posts: 2306
- Joined: Thu Jan 30, 2003 9:45 pm
- Location: norcal
- Location: Northern California, USA
- alimey4u2
- ICOA Web Video Director
- Posts: 5093
- Joined: Fri Aug 11, 2006 1:03 pm
- Location: Uphill, WsM, United Kingdom
Yup first production bike to lap the IOM at over 100mph was shod with K81's, they later called them TT100's....
Last edited by alimey4u2 on Fri Mar 13, 2009 7:50 am, edited 1 time in total.
ICOA # 656
- Highmileage
- Forum Regular
- Posts: 188
- Joined: Sun Dec 28, 2008 9:54 pm
- Location: Lower Slower Delaware, USA
- Location: Lower Slower Delaware, USA
I ran the K 81's on my Nortons back in the day, and they were okay for back then. But they were junk compared to what soon followed.Rick Pope wrote:Ohhhh!!! You bring back memories. I had a K81 on the front of my CB750...
The tires that I really loved were the Michelin M-45's that I used on my early GS 750's - they were a real bitch to mount (ridiculously stiff sidewalls) but they were fantastic tires!
- cbxtacy
- Posting God
- Posts: 2543
- Joined: Sun Aug 29, 2004 4:22 am
- Location: San Diego, California, USA
- Location: San Diego, California, USA
still make the K81
http://www.dunlopmotorcycle.com/tirecat ... d=9#tire47
either that or Dunlop has a lot left over from the 70's
http://www.dunlopmotorcycle.com/tirecat ... d=9#tire47
either that or Dunlop has a lot left over from the 70's
one out of four people in this country is mentally unbalanced
think of your three closest friends, if they're okay then
YOU'RE THE ONE
think of your three closest friends, if they're okay then
YOU'RE THE ONE