Page 2 of 3

Re: Cam cover oil leak - newbie

Posted: Thu Mar 15, 2012 8:36 am
by EMS
Rick Pope wrote:Spencer is correct. You can slip the cover out with the engine still in it's mounts, .
Yes, you can. You can also remove the carbs without titling the engine, as some people claim they have done. It is just a hell of a job and involves busted knuckles. Getting the cam cover out from between the frame and the cam gears and caps is like one of these trick novelty games where you have to fit a square peg through a round hole. Tilting the engine is not that bad of a job considering the aggravation you save yourself. It is also good maintenance practice.

Re: Cam cover oil leak - newbie

Posted: Thu Mar 15, 2012 12:20 pm
by daves79x
Agree with Mike on all points made.

Dave

Cam cover Tach oil leak now??

Posted: Sat Apr 07, 2012 8:46 pm
by xrdv8
Update - replaced the large gasket and the buttons and it still leaks. It looks like the leak is coming from the tach cable it self now and leaking donw onto the cam cover. Anyone seen this? Do I just replace the tach cable? I don't think any gasket is missing?

thanks!

Re: Cam cover Tach oil leak now??

Posted: Sat Apr 07, 2012 8:52 pm
by NobleHops
xrdv8 wrote:Update - replaced the large gasket and the buttons and it still leaks. It looks like the leak is coming from the tach cable it self now and leaking donw onto the cam cover. Anyone seen this? Do I just replace the tach cable? I don't think any gasket is missing?

thanks!
There is a seal in there, and it's easy to dislodge. DAMHIK.

N.

Re: Cam cover oil leak - newbie

Posted: Sun Apr 08, 2012 12:39 pm
by xrdv8
- what is the fix for that if you dislodge the seal? Take it out and put it back together? Thanks!

Re: Cam cover oil leak - newbie

Posted: Sun Apr 08, 2012 1:08 pm
by daves79x
What Nils is saying is that your tach cable seal is likely badly damaged or even missing altogether. You might stack a couple of o-rings of suitable size on the end of the cable, but likely a new cable is in order.

Dave

Re: Cam cover oil leak - newbie

Posted: Sun Apr 08, 2012 8:27 pm
by EMS
The tach drive has a "sahft seal" 8x16x6, p/n 91208-551-013/015 and an O-ring, 20mm 91302-704-000. Both parts are located under the tach drive cap. Why would he need a new cable??? If these seals are kaputt, a new cable will not stop the leak.

Re: Cam cover oil leak - newbie

Posted: Sun Apr 08, 2012 9:45 pm
by daves79x
We're talking about two different things. Yes, the actual tach drive housing has the seal and o-ring noted, and I should have mentioned those. They may indeed be the culprit. What I was referring to was the small oil seal in the end of the actual tach cable that is often missing and will cause a leak there.

Dave

Re: Cam cover oil leak - newbie

Posted: Mon Apr 09, 2012 3:39 pm
by xrdv8
hey guys, I think the seals under the drive housing are intact (I think!).

When the motor is running you can see the oil coming out of the very end of the tach cable housing - where the black housing ends just before the metal coupling part that fits into the motor. The black "seathing" seems to have backed off 1/8" or so exposing the inner cable deal and then leaks down onto the cover and then the engine. For the money i guess I should just replace the cable first. I looked at the innards of the housing and the seals seem to be there.

thanks again!

Re: Cam cover oil leak - newbie

Posted: Mon Apr 09, 2012 4:20 pm
by EMS
I am still a little confused here. Aren't the two inner seals (one of them is quite a elaborate design "shaft seal"-type) supposed to prevent any oil from coming out of the valve cover/tach drive???
The easiest way to check is, to take the tach cable of and run the engine. If oil is coming out of the tach drive connection....

Re: Cam cover oil leak - newbie

Posted: Mon Apr 09, 2012 4:33 pm
by daves79x
Mike:

Yes, in theory, you are correct. There should be no oil seeping out of the top of the housing and into the cable. But Honda put that special little seal in the end of the tach cable for a reason - maybe just to keep water and dirt out of the housing, but it also seals any oil that may seep past the inner seal. I'd actually replace the housing seal also - available and easy to do.

Dave

Re: Cam cover oil leak - newbie

Posted: Tue Apr 29, 2014 4:31 pm
by pgilliam1
I'm looking for replacements for the cam cover bolt seals on a 1981. I see 2 sources listed on this thread, but I can't seem to locate either of them. Can someone give me another source besides the dealership? Also, there are several types listed on eBay for 750CB's that look similar, but I'm not sure of the fit. Are there replacements from other bikes? TIA.

Re: Cam cover oil leak - newbie

Posted: Tue Apr 29, 2014 5:02 pm
by EMS
This auction is from Bob Frantzke, Performance International. He knows CBXes


http://www.ebay.com/itm/80-82-Honda-CBX ... dd&vxp=mtr

here is another one

http://www.ebay.com/itm/HONDA-OEM-CBX-C ... 86&vxp=mtr

Re: Cam cover oil leak - newbie

Posted: Tue Apr 29, 2014 6:22 pm
by daves79x
Good links, Mike. If you are looking for other-than-NOS seals for the '80-'82, there aren't any I know of. You're stuck buying Honda ones from the dealer, or sources such as Mike links to. Don't be tempted to get the aftermarket early model ones - they aren't correct for your bike.

Dave

Re: Cam cover oil leak - newbie

Posted: Tue Apr 29, 2014 9:11 pm
by pgilliam1
Thanks Dave and Mike. By the time I pay shipping, the dealers price is just as good. I'm surprised that such a simple part wasn't reused from other bikes.