C5 aftermarket ignition woes
-
- Forum Regular
- Posts: 41
- Joined: Wed Mar 09, 2016 4:21 pm
- Location: Watford, just north of London
- Location: Watford, England
C5 aftermarket ignition woes
Is there anyone on the forum who has a C5 ignition system fitted, who lives in UK, preferably in the south, as i am from Watford, Herts . I have some running issues and would like to have a chat with someone with the same system, help would be appreciated, regards cbxchris
-
- ICOA Member
- Posts: 569
- Joined: Fri Jun 12, 2015 9:56 am
- Location: Canmore Alberta Canada
- Location: Canmore Alberta Canada
Re: C5 aftermarket ignition woes
Hi Chris
I'm not from The UK but I am running a C5 ignition. I also had running issues when first installed and contacted C5.
My issue turned out to be that I did not have the cyl at exactly Top Dead Center.(I was a hair off) Once that was rectified the bike ran way better.
Hope that helps.
Mouse
I'm not from The UK but I am running a C5 ignition. I also had running issues when first installed and contacted C5.
My issue turned out to be that I did not have the cyl at exactly Top Dead Center.(I was a hair off) Once that was rectified the bike ran way better.
Hope that helps.
Mouse
Canadian Amateur Radio Call sign VE6 VES
-
- Forum Regular
- Posts: 41
- Joined: Wed Mar 09, 2016 4:21 pm
- Location: Watford, just north of London
- Location: Watford, England
Re: C5 aftermarket ignition woes
Thanks for the input Mouse.Mouse wrote:Hi Chris
I'm not from The UK but I am running a C5 ignition. I also had running issues when first installed and contacted C5.
My issue turned out to be that I did not have the cyl at exactly Top Dead Center.(I was a hair off) Once that was rectified the bike ran way better.
Hope that helps.
Mouse
-
- Forum Regular
- Posts: 107
- Joined: Sun Feb 10, 2013 10:40 pm
- Location: Galway Ireland
- Location: Galway Ireland
Re: C5 aftermarket ignition woes
Hi Chris,
I am in Ireland and have 2 prolinks.
One runs C5 the other stock ignition.
I got the C5 (bought 4 sets) because i wanted a rev limiter and no igniters.
Both bikes run the same if anything i think the stock bike runs slightly better but not much in it.
The C5 runs fine with no issues.
As per ignition timing it makes no difference how it is set the bike runs the same??????????
Why I dont know, I was in France a couple of years ago and decided to play with the timing.
I loosened the C5 plate and rotated it both ways within the slack of the wiring.
tried it a good 15 to 20 deg rotation both ways, did test runs and the bike ran well both ways.
In the end I just moved the plate and revved the engine until it sounded the strongest and tightened up the plate.
Its been like that ever since including a fast run from Fuengirola to Cherbourg (1200 miles in 18 hours including stops).
I always ment to contact Paul and discuss the phenomenon but never got around to it.
I am in Ireland and have 2 prolinks.
One runs C5 the other stock ignition.
I got the C5 (bought 4 sets) because i wanted a rev limiter and no igniters.
Both bikes run the same if anything i think the stock bike runs slightly better but not much in it.
The C5 runs fine with no issues.
As per ignition timing it makes no difference how it is set the bike runs the same??????????
Why I dont know, I was in France a couple of years ago and decided to play with the timing.
I loosened the C5 plate and rotated it both ways within the slack of the wiring.
tried it a good 15 to 20 deg rotation both ways, did test runs and the bike ran well both ways.
In the end I just moved the plate and revved the engine until it sounded the strongest and tightened up the plate.
Its been like that ever since including a fast run from Fuengirola to Cherbourg (1200 miles in 18 hours including stops).
I always ment to contact Paul and discuss the phenomenon but never got around to it.
-
- Forum Regular
- Posts: 41
- Joined: Wed Mar 09, 2016 4:21 pm
- Location: Watford, just north of London
- Location: Watford, England
Re: C5 aftermarket ignition woes
Thanks for the input Patzx12, still trying to sort mine out, will post if and when sorted ! ![Smile :-)](./images/smilies/icon/smile.gif)
![Smile :-)](./images/smilies/icon/smile.gif)
-
- Forum Regular
- Posts: 107
- Joined: Sun Feb 10, 2013 10:40 pm
- Location: Galway Ireland
- Location: Galway Ireland
Re: C5 aftermarket ignition woes
There is not a lot to figure out it is such a simple setup.
Remove the advance retard unit, fit the C5, fit the coils. wire up and set the timing.
That is it, if it is not running properly there is nothing to adjust.
Get on to C5 if you think you have an issue with the unit.
Remove the advance retard unit, fit the C5, fit the coils. wire up and set the timing.
That is it, if it is not running properly there is nothing to adjust.
Get on to C5 if you think you have an issue with the unit.
-
- New Member & Happy To Be Here
- Posts: 13
- Joined: Sun Mar 04, 2018 12:06 pm
- Location: Saudi
- Location: Saudi
Re: C5 aftermarket ignition woes
I always wanted to know how these performed
Cause I would like to change the stock ignitors
Cause I would like to change the stock ignitors
-
- Forum Regular
- Posts: 41
- Joined: Wed Mar 09, 2016 4:21 pm
- Location: Watford, just north of London
- Location: Watford, England
Re: C5 aftermarket ignition woes
Kar1zma wrote:I always wanted to know how these performed
Cause I would like to change the stock ignitors
I bought a C5 ignition and did not work properly, could not get a refund, so bought a Dyna system and runs great !
-
- Forum Regular
- Posts: 107
- Joined: Sun Feb 10, 2013 10:40 pm
- Location: Galway Ireland
- Location: Galway Ireland
Re: C5 aftermarket ignition woes
My CBX with C5 is still running well. I contacted Paul on FB and he got right back to me and told me to send the unit back if i had issues.
I dont have any issues and it is a simple setup.
I would like to see the ADV - Retard is action, like say with a timing light but I dont think that is possible due to it being an electronic process.
The bike is due a service and I will mess about with it a bit to see if i can learn a bit more about it.
I dont have any issues and it is a simple setup.
I would like to see the ADV - Retard is action, like say with a timing light but I dont think that is possible due to it being an electronic process.
The bike is due a service and I will mess about with it a bit to see if i can learn a bit more about it.